[Nov-2026] Dumps Brief Outline Of The JN0-664 Exam - VCE4Dumps
JN0-664 Training & Certification Get Latest JNCIP-SP
To be eligible to take the JN0-664 exam, candidates must have a valid JNCIS-SP certification or possess equivalent knowledge and experience in service provider networking. JN0-664 exam is computer-based and consists of 65 multiple-choice questions, which must be completed in 120 minutes.
NEW QUESTION # 20
Which three statements about IS-IS in a multi-area network are correct? (Choose three.)
- A. External L2 PDUs are flooded to all L2 routers in other areas.
- B. Internal L1 PDUs are only flooded to the local area's L1 routers.
- C. Internal L1 PDUs are flooded to all L1 routers in other areas.
- D. Internal L1 PDUs are flooded to the local area's L2 routers.
- E. External L2 PDUs are only flooded to the local area's L2 routers.
Answer: A,B,D
Explanation:
Intermediate System to Intermediate System (IS-IS) is a link-state routing protocol designed to move information efficiently within a computer network, a group of physically connected computers or similar devices. It operates in two levels, Level 1 (L1) and Level 2 (L2), and supports hierarchical routing within a multi-area network.
Let's analyze each statement to determine its correctness in the context of IS-IS multi-area networks.
1. **Statement A: Internal L1 PDUs are flooded to the local area's L2 routers.**
- This statement is correct. L1 PDUs (Protocol Data Units) are flooded within the L1 area and also to the L2 routers that are present in the same area. These L2 routers act as the boundary routers that connect the local L1 area to other L1 areas via L2.
2. **Statement B: External L2 PDUs are flooded to all L2 routers in other areas.**
- This statement is correct. L2 PDUs are flooded throughout the entire L2 backbone, which includes all L2 routers in different areas. This ensures that inter-area routing information is shared across the network.
3. **Statement C: Internal L1 PDUs are flooded to all L1 routers in other areas.**
- This statement is incorrect. Internal L1 PDUs are only flooded within the local L1 area. They do not cross L1 area boundaries; inter-area communication is handled by L2 routers.
4. **Statement D: Internal L1 PDUs are only flooded to the local area's L1 routers.**
- This statement is correct. Internal L1 PDUs are indeed only flooded within their local L1 area, and do not go beyond it.
5. **Statement E: External L2 PDUs are only flooded to the local area's L2 routers.**
- This statement is incorrect. External L2 PDUs are flooded to all L2 routers throughout the IS-IS network, not just to those in the local area. This allows L2 routers to maintain a complete map of the network's topology.
**Conclusion**:
Given the analysis, the correct answers are:
**A. Internal L1 PDUs are flooded to the local area's L2 routers.**
**B. External L2 PDUs are flooded to all L2 routers in other areas.**
**D. Internal L1 PDUs are only flooded to the local area's L1 routers.**
**Reference**:
- Juniper Networks Documentation on IS-IS: [IS-IS Overview](https://www.juniper.net/documentation/en_US/junos/topics/concept/is-is-routing-overview.html)
- RFC 1195, Use of OSI IS-IS for Routing in TCP/IP and Dual Environments: [RFC 1195](https://tools.ietf.org/html/rfc1195) which details the operation of IS-IS in multi-area networks.
NEW QUESTION # 21
You are configuring anycast RP for load balancing and redundancy in your PIM-SM domain. You want to share active sources between RPs.
In this scenario, what are two solutions that will accomplish this task? (Choose two.)
- A. Configure MSDP on each source DR router.
- B. Configure MSDP on each RP router.
- C. Configure anycast PIM with the rp-set statement on each RP router.
- D. Configure anycast PIM with the rp-set statement on each source DR router.
Answer: B,C
Explanation:
In a PIM Sparse Mode (PIM-SM) domain, Anycast RP is used for load balancing and redundancy by configuring multiple RPs with the same IP address. However, for active multicast sources to be shared between RPs, an additional mechanism is needed since PIM-SM does not automatically synchronize sources between RPs.
Evaluating the Answer Choices
Option A: "Configure MSDP on each RP router." ✅
Multicast Source Discovery Protocol (MSDP) is required in an Anycast RP setup to share active source information between RPs.
MSDP allows RPs to exchange source-active (SA) messages, ensuring that multicast receivers in different regions can still receive traffic from sources registered with different RPs.
Juniper Documentation confirms that MSDP is used to synchronize active sources across multiple RPs in an Anycast RP deployment.
✅ This is a correct answer.
Option B: "Configure anycast PIM with the rp-set statement on each RP router." ✅ Anycast PIM allows multiple RPs to share the same IP address, and the rp-set statement is used to define the set of Anycast RPs.
This enables receivers and sources to register with the closest RP.
However, Anycast PIM alone does not share active source information between RPs; MSDP is still needed for that.
The combination of Anycast PIM (rp-set) and MSDP is the correct approach.
✅ This is a correct answer.
NEW QUESTION # 22
Exhibit
CE-1 must advertise ten subnets to PE-1 using BGP Once CE-1 starts advertising the subnets to PE-1, the BGP peering state changes to Active.
Referring to the CLI output shown in the exhibit, which statement is correct?
- A. The prefix limit has been reached on PE-1
- B. CE-1 is configured with an incorrect peer AS
- C. CE-1 is unreachable
- D. CE-1 is advertising its entire routing table.
Answer: A
Explanation:
Analyzing the Exhibit and Understanding the Issue
The exhibit shows BGP configurations on CE-1 and PE-1, which are connected via EBGP.
CE-1 (Customer Edge)
Uses AS 64511 and establishes an EBGP session with PE-1 (AS 65550).
Configured to export 10 static routes (192.168.1.0/24 - 192.168.10.0/24) using the static-to-bgp policy.
PE-1 (Provider Edge)
Uses AS 65550 and is peering with CE-1 (AS 64511).
Configured with a prefix-limit of 5 on received routes from CE-1.
Teardown enabled, meaning if more than 5 prefixes are received, the BGP session is shut down.
Identifying the Problem
CE-1 is correctly configured with peer AS 65550, so Option B ("CE-1 is configured with an incorrect peer AS") is incorrect ❌.
CE-1 is advertising exactly 10 static routes (as per policy).
PE-1 has a prefix-limit maximum 5 with teardown enabled.
This means that when CE-1 advertises more than 5 prefixes, PE-1 shuts down the BGP session.
BGP moves to the "Active" state, indicating that the session has been disrupted and PE-1 is trying to re-establish the connection.
CE-1 is reachable since the session was initially established before the limit was exceeded, so Option D ("CE-1 is unreachable") is incorrect ❌.
CE-1 is not advertising its entire routing table, only the static prefixes listed in the policy, so Option A ("CE-1 is advertising its entire routing table") is incorrect ❌.
Correct Answer
✅ C. The prefix limit has been reached on PE-1
Verification from Juniper Documentation
Juniper BGP Prefix Limit Documentation confirms that exceeding the prefix limit with teardown causes the BGP session to go into "Active" state.
Juniper Troubleshooting Guide for BGP Peering Issues states that when a BGP session reaches the prefix limit and has teardown enabled, the session is terminated.
NEW QUESTION # 23
You are asked to protect your company's customers from amplification attacks.
In this scenario, what is Juniper's recommended protection method?
- A. destination-based Remote Triggered Black Hole
- B. ASN prepending
- C. BGP FlowSpec
- D. unicast Reverse Path Forwarding
Answer: C
NEW QUESTION # 24
Exhibit
Referring to the exhibit, which two statements are correct about the dual route reflectors within a cluster?
(Choose two.)
- A. RR1 advertises routes from the client to RR2. using itself as the next hop.
- B. RR1 and RR2 append the duster ID when advertising routes from dient to dient.
- C. RR1 and RR2 must have the same duster ID to exchange routes learned from the client.
- D. RR1 and RR2 advertise routes learned from the clients to EBGP peers, using itself as the next hop.
Answer: B,D
NEW QUESTION # 25
In IS-IS, which two statements are correct about the designated intermediate system (DIS) on a multi-access network segment? (Choose two)
- A. A router with a priority of 1 wins the DIS election over a router with a priority of 10.
- B. On the multi-access network, each router only forms an adjacency to the DIS.
- C. A router with a priority of 10 wins the DIS election over a router with a priority of 1.
- D. On the multi-access network, each router forms an adjacency to every other router on the segment
Answer: C,D
Explanation:
Option A (Correct):
In IS-IS, the Designated Intermediate System (DIS) is elected based on the highest configured priority (as defined in Junos OS).
If priorities are equal, the router with the highest MAC address becomes the DIS.
A priority value of 10 will always override a lower priority (e.g., 1).
Reference:
Option C (Correct):
On a multi-access network (e.g., Ethernet), all IS-IS routers form adjacencies with every other router on the segment.
Unlike OSPF, IS-IS does not restrict adjacencies to only the DIS.
The DIS is responsible for creating a pseudonode LSP to represent the broadcast network, but full mesh adjacencies are maintained.
Why Other Options Are Incorrect:
Option B: Incorrect. Higher priority always wins the DIS election. A priority of 1 cannot override a priority of 10.
Option D: Incorrect. IS-IS routers form adjacencies with all neighbors, not just the DIS.
Key Takeaways:
DIS Election: Prioritizes highest numerical value (e.g., 10 > 1).
Adjacency Behavior: Full mesh adjacencies are maintained, unlike OSPF.
DIS Role: Primarily for generating pseudonode LSPs and optimizing flooding, not adjacency restriction.
For further details, refer to Juniper's official IS-IS documentation:
Juniper IS-IS Configuration Guide.
https://www.juniper.net/documentation/us/en/software/junos/is-is/topics/concept/routing-protocol-is-is-security-designated-router-understanding.html
NEW QUESTION # 26
Which statement is correct about IS-IS when it performs the Dijkstra algorithm?
- A. Tuples with the lowest cost are moved from the tree database to the LSDB.
- B. The local router moves its own local tuples into the candidate database
- C. The algorithm will stop processing once the tree database is empty.
- D. When a new neighbor ID in the tree database matches a router ID in the LSDB, the neighbor ID is moved to the candidate database
Answer: B
Explanation:
IS-IS is a link-state routing protocol that uses the Dijkstra algorithm to compute the shortest paths between nodes in a network. The Dijkstra algorithm maintains three data structures: a tree database, a candidate database, and a link-state database (LSDB). The tree database contains the nodes that have been visited and their shortest distances from the source node. The candidate database contains the nodes that have not been visited yet and their tentative distances from the source node. The LSDB contains the topology information of the network, such as the links and their costs.
The Dijkstra algorithm works as follows:
The local router moves its own local tuples into the tree database. A tuple consists of a node ID, a distance, and a parent node ID. The local router's tuple has a distance of zero and no parent node.
The local router moves its neighbors' tuples into the candidate database. The neighbors' tuples have distances equal to the costs of the links to them and parent node IDs equal to the local router's node ID.
The local router selects the tuple with the lowest distance from the candidate database and moves it to the tree database. This tuple becomes the current node.
The local router updates the distances of the current node's neighbors in the candidate database by adding the current node's distance to the link costs. If a shorter distance is found, the parent node ID is also updated.
The algorithm repeats steps 3 and 4 until either the destination node is reached or the candidate database is empty.
NEW QUESTION # 27
Exhibit
Referring to the exhibit, which three statements are correct about route 10 0 0.0/16 when using the default BGP advertisement rules'? (Choose three.)
- A. R1 will prepend AS 65531 when advertising 10 0.0 0/16 to R2.
- B. R1 will advertise 10.0.0.0/16 to R2 with 192 168 1 1 as the next hop.
- C. R2 will advertise 10.0.0.0/16 to R3 with 192.168.1 1 as the next hop
- D. R2 will advertise 10.0.0.0/16 to R4 with 172.16.1.1 as the next hop
- E. R4 will advertise 10 0.0 0/16 to R6 with 172.16 1 1 as the next hop
Answer: B,D,E
Explanation:
Explanation
The problem in this scenario is that R1 and R8 are not receiving each other's routes because of private AS numbers in the AS path. Private AS numbers are not globally unique and are not advertised to external BGP peers. To solve this problem, you need to do the following:
* Configure loops on routers in AS 65412 and advertise-peer-as on routers in AS 64498. This allows R5 and R6 to advertise their own AS number (65412) instead of their peer's AS number (64498) when sending updates to R7 and R8. This prevents a loop detection issue that would cause R7 and R8 to reject the routes from R5 and R62
* Configure remove-private on advertisements from AS 64497 toward AS 64498 and from AS 64500 toward AS 64499. This removes any private AS numbers from the AS path before sending updates to external BGP peers. This allows R2 and R3 to receive the routes from R1 and R4, respectively3.
NEW QUESTION # 28
Exhibit
You are examining an L3VPN route that includes the information shown in the exhibit Which statement is correct in this scenario?
- A. The information shows a Type 1 route distinguisher.
- B. The information shows a route target
- C. The information shows a Type 2 route distinguisher.
- D. The information shows a Type 0 route distinguisher
Answer: A
Explanation:
Type 1: When Type value is 1, the Administrator field is 4-bytes and Assigned Number field is 2-bytes. The Administrator field should be set to the IP address (public IP addresses should be used). The Assigned Number field contains a number from a numbering space that is administered by the enterprise to which the IP address has been assigned by the appropriate authority.
NEW QUESTION # 29
Which two statements about the configuration shown in the exhibit are correct? (Choose two.)
- A. This VPN connects customer sites that use the same AS number.
- B. A Layer 3 VPN is configured.
- C. This VPN connects customer sites that use different AS numbers.
- D. A Layer 2 VPN is configured.
Answer: A,B
NEW QUESTION # 30
After a recent power outage, your manager asks you to investigate ways to automatically reduce the impact caused by suboptimal routing in your OSPF and OSPFv3 network after devices reboot.
Which three configuration statements accomplish this task? (Choose three.)
- A. set protocols ospf overload
- B. set protocols ospf3 overload timeout 900
- C. set protocols ospf3 overload
- D. set protocols ospf overload timeout 900
- E. set protocols ospf3 realm ipv4-unicast overload timeout 900
Answer: B,D,E
Explanation:
To reduce the impact of suboptimal routing in OSPF and OSPFv3 after devices reboot, you can use the overload feature to prevent a router from being used as a transit router for a specified period of time. This allows the router to stabilize its routing table before forwarding traffic for other routers. To enable the overload feature, you need to do the following:
For OSPF, configure the overload statement under [edit protocols ospf] hierarchy level. You can also specify a timeout value in seconds to indicate how long the router should remain in overload state after it boots up. For example, set protocols ospf overload timeout 900 means that the router will be in overload state for 15 minutes after it boots up.
For OSPFv3, configure the overload statement under [edit protocols ospf3] hierarchy level. You can also specify a realm (ipv4-unicast or ipv6-unicast) and a timeout value in seconds to indicate how long the router should remain in overload state after it boots up for each realm. For example, set protocols ospf3 realm ipv4-unicast overload timeout 900 means that the router will be in overload state for 15 minutes after it boots up for IPv4 unicast routing.
NEW QUESTION # 31 
Click the Exhibit button.
Which two statements are correct about the class-of-service configuration shown in the exhibit? (Choose two.)
- A. The best-effort queue can never transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, even if that bandwidth is available.
- B. Incoming traffic will be classified using the default classifier.
- C. Incoming traffic will not be classified because no classifier exists in the configuration.
- D. The best-effort queue can transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, if no other queue is using that bandwidth.
Answer: C,D
Explanation:
The class-of-service (CoS) configuration in the exhibit shows how traffic is scheduled on the ge-0/0/0 interface. Let's analyze each statement to determine its correctness:
A: Incoming traffic will not be classified because no classifier exists in the configuration.
* This statement is correct. The configuration shown does not include any classifier, so no explicit classification is defined. As a result, incoming traffic will not be classified according to any custom criteria.
B: The best-effort queue can transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, if no other queue is using that bandwidth.
* This statement is correct. The transmit-rate percent 40 means that 40% of the bandwidth is guaranteed for the best-effort queue, but it can use more bandwidth if other queues (like the priority scheduler) are not utilizing their allocated bandwidth.
C: Incoming traffic will be classified using the default classifier.
* This statement is incorrect. Without an explicit classifier in the configuration, there is no mention of a default classifier being used. Therefore, the incoming traffic won't be classified based on the configuration shown.
D: The best-effort queue can never transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, even if that bandwidth is available.
* This statement is incorrect. The transmit-rate percent 40 sets a guaranteed minimum bandwidth but does not set a maximum limit. The best-effort queue can utilize more bandwidth if other queues are not using their allocated portions.
NEW QUESTION # 32
Which two statements are correct about the class-of-service configuration shown in the exhibit?
(Choose two.)
- A. The best-effort queue can never transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, even if that bandwidth is available.
- B. Incoming traffic will not be classified because no classifier exists in the configuration.
- C. Incoming traffic will be classified using the default classifier.
- D. The best-effort queue can transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, if no other queue is using that bandwidth.
Answer: C,D
NEW QUESTION # 33
You have an EVI implemented between PE-1, PE-2, and PE-3 to allow communication between CE-1 and CE-2. CE-2 receives unicast traffic from CE-1 on both links to PE-2 and PE-3. When CE-1 sends broadcast traffic. CE-2 receives it on only one of the multihomed links.
Referring to the exhibit, which EVPN route type enables this behavior?
- A. Type 2
- B. Type 1
- C. Type 3
- D. Type 4
Answer: D
NEW QUESTION # 34
Refer to the exhibit.
Click the Exhibit button.
You have an EVI implemented between PE-1, PE-2, and PE-3 to allow communication between CE-1 and CE-2. CE-2 receives unicast traffic from CE-1 on both links to PE-2 and PE-3. When CE-1 sends broadcast traffic, CE-2 receives it on only one of the multihomed links.
Referring to the exhibit, which EVPN route type enables this behavior?
- A. Type 2
- B. Type 4
- C. Type 1
- D. Type 3
Answer: D
Explanation:
In the context of Ethernet VPN (EVPN) and the behavior described in the exhibit, it's essential to understand the different EVPN route types and their specific functionalities. Here, CE-2 is receiving unicast traffic on both of its multihomed links to PE-2 and PE-3, but broadcast traffic is received only on one of these links.
**Explanation of EVPN Route Types**:
1. **Type 1 (Ethernet Auto-Discovery Routes)**:
- These routes are used for auto-discovery of Ethernet segments and for advertising VLAN membership.
- They do not directly influence the behavior described in the question.
2. **Type 2 (MAC/IP Advertisement Routes)**:
- These routes are used to advertise MAC addresses and IP-to-MAC bindings within the EVPN.
- They handle unicast traffic forwarding and are crucial for populating the MAC address tables on the PE devices.
- While important, they do not explain the selective broadcast behavior.
3. **Type 3 (Inclusive Multicast Ethernet Tag Routes)**:
- These routes are used to build multicast distribution trees for delivering broadcast, unknown unicast, and multicast (BUM) traffic.
- They ensure that BUM traffic is sent only once per Ethernet segment, preventing duplicate frames from being sent to multihomed CEs.
- This aligns with the behavior described where CE-2 receives broadcast traffic on only one link to prevent duplication.
4. **Type 4 (Ethernet Segment Routes)**:
- These routes are used to advertise the presence of an Ethernet segment and are crucial for Designated Forwarder (DF) election processes in multihoming scenarios.
- While relevant to multihoming, they are not directly responsible for the selective broadcast behavior.
**Conclusion**:
The behavior described, where CE-2 receives broadcast traffic on only one of its multihomed links, is controlled by Type 3 routes. These routes are specifically designed to handle inclusive multicast and broadcast traffic efficiently in EVPN environments, ensuring that such traffic is not duplicated across multiple links to the same CE.
**Reference**:
- Juniper Networks EVPN Documentation: [EVPN Overview](https://www.juniper.net/documentation/en_US/junos/topics/concept/evpn-overview.html)
- RFC 7432, BGP MPLS-Based Ethernet VPN: [RFC 7432](https://tools.ietf.org/html/rfc7432) provides detailed descriptions of EVPN route types and their functions.
- Junos OS EVPN Configuration Guide: [Junos OS EVPN Configuration Guide](https://www.juniper.net/documentation/en_US/junos/topics/topic-map/evpn.html)
NEW QUESTION # 35
Exhibit
Click the Exhibit button-Referring to the exhibit, which two statements are correct about BGP routes on R3 that are learned from the ISP-A neighbor? (Choose two.)
- A. By default, the next-hop value for these routes is not changed by ISP-A before being sent to R3.
- B. All BGP attribute values must be removed before receiving the routes.
- C. The BGP local-preference value that is used by ISP-A is not advertised to R3.
- D. The next-hop value for these routes is changed by ISP-A before being sent to R3.
Answer: A,C
Explanation:
BGP is an exterior gateway protocol that uses path vector routing to exchange routing information among autonomous systems. BGP uses various attributes to select the best path to each destination and to propagate routing policies. Some of the common BGP attributes are AS path, next hop, local preference, MED, origin, weight, and community. BGP attributes can be classified into four categories: well-known mandatory, well-known discretionary, optional transitive, and optional nontransitive. Well-known mandatory attributes are attributes that must be present in every BGP update message and must be recognized by every BGP speaker.
Well-known discretionary attributes are attributes that may or may not be present in a BGP update message but must be recognized by every BGP speaker. Optional transitive attributes are attributes that may or may not be present in a BGP update message and may or may not be recognized by a BGP speaker. If an optional transitive attribute is not recognized by a BGP speaker, it is passed along to the next BGP speaker. Optional nontransitive attributes are attributes that may or may not be present in a BGP update message and may or may not be recognized by a BGP speaker. If an optional nontransitive attribute is not recognized by a BGP speaker, it is not passed along to the next BGP speaker. In this question, we have four routers (R1, R2, R3, and R4) that are connected in a full mesh topology and running IBGP. R3 receives the 192.168.0.0/16 route from its EBGP neighbor and advertises it to R1 and R4 with different BGP attribute values. We are asked which statements are correct about the BGP routes on R3 that are learned from the ISP-A neighbor. Based on the information given, we can infer that the correct statements are:
By default, the next-hop value for these routes is not changed by ISP-A before being sent to R3. This is because the default behavior of EBGP is to preserve the next-hop attribute of the routes received from another EBGP neighbor. The next-hop attribute indicates the IP address of the router that should be used as the next hop to reach the destination network.
The BGP local-preference value that is used by ISP-A is not advertised to R3. This is because the local-preference attribute is a well-known discretionary attribute that is used to influence the outbound traffic from an autonomous system. The local-preference attribute is only propagated within an autonomous system and is not advertised to external neighbors.
References: : https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html :
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13762-40.html :
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13759-37.html
NEW QUESTION # 36
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. VPN routes are exported with only the target:65512:1 route target
- B. You cannot use the vrf-target and vrf-export statements in the same VRF.
- C. VPN routes are exported with the target:65512:1 and target:65512:2 route targets.
- D. VPN routes with the target:65512:1 and target:65512:2 route targets are imported.
Answer: C
Explanation:
The exhibit shows the configuration of a VRF (Virtual Routing and Forwarding) instance on a Juniper PE router. Let's break down the key components:
VRF Configuration (VPN-A)
The instance type is VRF, meaning this is an L3VPN (Layer 3 VPN).
The routing instance contains a static route (10.1.0.0/16 next-hop 10.1.0.1).
The interface ge-0/0/2.0 is assigned to the VRF.
Route Distinguisher (RD): 172.17.20.1:1
VRF-Export Policy: vpn-a-export
VRF-Target: target:65512:1 (This defines which routes will be imported into the VRF).
VRF Export Policy (vpn-a-export)
The vpn-a-export policy adds two BGP communities (route targets) to exported VPN routes:
community add vpn-a-target;
community add vpn-m-target;
accept;
The vpn-a-target community corresponds to target:65512:1.
The vpn-m-target community corresponds to target:65512:2.
Policy-Options (Community Definitions)
community vpn-a-target members target:65512:1;
community vpn-m-target members target:65512:2;
This confirms that routes exported from this VRF will have BOTH target:65512:1 and target:65512:2.
Evaluating the Answer Choices
✅ Option A: "VPN routes are exported with the target:65512:1 and target:65512:2 route targets." The vpn-a-export policy explicitly adds both vpn-a-target (65512:1) and vpn-m-target (65512:2) to exported routes.
This is correct. ✅
❌ Option B: "You cannot use the vrf-target and vrf-export statements in the same VRF." This is incorrect.
Juniper allows the use of both vrf-target and vrf-export in the same VRF:
vrf-target is used for importing routes.
vrf-export defines export policies (which can add additional route targets).
This is incorrect. ❌
❌ Option C: "VPN routes with the target:65512:1 and target:65512:2 route targets are imported." The vrf-target target:65512:1; statement only controls importing routes.
The import policy does not include target:65512:2, so routes tagged with target:65512:2 alone would not be imported into this VRF.
This is incorrect. ❌
❌ Option D: "VPN routes are exported with only the target:65512:1 route target." The export policy (vpn-a-export) clearly adds both 65512:1 and 65512:2.
This is incorrect. ❌
Final answer:
✅ A. VPN routes are exported with the target:65512:1 and target:65512:2 route targets.
Verification from Juniper Documentation
Juniper MPLS L3VPN Configuration Guide confirms that vrf-target is used for importing, while vrf-export can be used for exporting multiple route targets.
Juniper Routing Policy Documentation states that export policies can add multiple BGP communities (route targets).
RFC 4364 (BGP/MPLS IP VPNs) defines the use of route targets for VPN route control.
NEW QUESTION # 37
Refer to the exhibit.

Click the Exhibit button.
Referring to the exhibit, which two statements are correct regarding the output shown in the exhibit? (Choose two.)
- A. The multicast group is an ASM group.
- B. The multicast group is an SSM group.
- C. The multicast traffic is using the SPT.
- D. The multicast traffic is using the RPT.
Answer: A,C
Explanation:
In the provided exhibit, the output of the `show pim join extensive 232.1.1.1` command is shown. This command provides detailed information about the PIM join state for the specified multicast group (232.1.1.1) on the router R1. To determine the correct statements regarding the multicast traffic, let's analyze the output and the terms involved:
1. **ASM vs. SSM**:
- **ASM (Any-Source Multicast)**: In ASM, receivers are interested in receiving multicast traffic from any source sending to a particular multicast group.
- **SSM (Source-Specific Multicast)**: In SSM, receivers are interested in receiving traffic only from specific sources for a multicast group.
- **Group Address Range**:
- ASM uses the range 224.0.0.0 to 239.255.255.255.
- SSM uses the range 232.0.0.0 to 232.255.255.255.
Since the group address 232.1.1.1 falls within the SSM range (232.0.0.0/8), there might be confusion. However, considering the flags and states in the output, it's evident that the PIM mode and source information are consistent with ASM behavior.
2. **Multicast Trees**:
- **RPT (Rendezvous Point Tree)**: Multicast traffic initially uses the RPT, where the Rendezvous Point (RP) acts as an intermediate point.
- **SPT (Shortest Path Tree)**: After the initial join via RPT, traffic can switch to SPT, which is a direct path from the source to the receiver.
3. **Output Analysis**:
- **Flags**:
- The flags `sparse, rp-tree, wildcard` indicate that the group 232.1.1.1 is currently using RPT. This is typical for ASM, where traffic initially goes through the RP.
- The flags `sparse, spt` indicate that for the source 172.16.1.2, traffic has switched to SPT, meaning it is using the shortest path from the source directly to the receivers.
**Conclusion**:
Based on the analysis:
- **A. The multicast group is an ASM group**: This statement is correct as the configuration and behavior indicate ASM operation.
- **B. The multicast traffic is using the SPT**: This statement is also correct because the flags for the source 172.16.1.2 indicate that the traffic is using the SPT.
Thus, the correct answers are:
**A. The multicast group is an ASM group.**
**B. The multicast traffic is using the SPT.**
**Reference**:
- Juniper Networks PIM Documentation: [PIM Overview](https://www.juniper.net/documentation/en_US/junos/topics/concept/pim-overview.html)
- Junos OS Multicast Routing Configuration Guide: [Multicast Routing Configuration Guide](https://www.juniper.net/documentation/en_US/junos/topics/topic-map/multicast-routing.html)
NEW QUESTION # 38
Refer to the exhibit.
Click the Exhibit button.
Which two statements are correct about the class-of-service configuration shown in the exhibit? (Choose two.)
- A. The best-effort queue can never transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, even if that bandwidth is available.
- B. Incoming traffic will not be classified because no classifier exists in the configuration.
- C. Incoming traffic will be classified using the default classifier.
- D. The best-effort queue can transmit more than 40% of the total bandwidth on the ge-0/0/0 interface, if no other queue is using that bandwidth.
Answer: C,D
Explanation:
https://www.juniper.net/documentation/us/en/software/junos/traffic-mgmt-qfx/topics/concept/cos-qfx-series-default-scheduling-classification-understanding.html
NEW QUESTION # 39
A router running IS-IS is configured with an ISO address of 49.0001.00a0.c96b.c490.00.
Which part of this address is the system ID?
- A. 00a0.c96b.c490 is the system identifier.
- B. 0001.00a0.c96b.c490 is the system identifier.
- C. c490 is the system identifier.
- D. c96b.c490 is the system identifier.
Answer: A
NEW QUESTION # 40
Exhibit
Referring to the exhibit, you must provide Internet access for VPN-A using CE-1 as the hub CE.
Which two statements are correct in this situation? (Choose two.)
- A. RIB groups are not needed to leak routes between the inet. 0 and VPN-A. inet. 0 tables,
- B. Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> GW-1.
- C. You must use RIB groups to leak routes between the inet. o and vpn-a. inet. o tables.
- D. Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> CE-1 -> PE-1 -> GW-1.
Answer: A,D
NEW QUESTION # 41
You must ensure that the VPN backbone is preferred over the back door intra-area link as long as the VPN is available.
Referring to the exhibit, which action will accomplish this task?
- A. Create an OSPF sham link between the PE routers.
- B. Configure the OSPF metric on the backup intra-area link that is higher than the L3VPN link.
- C. Enable OSPF traffic-engineering.
- D. Configure an import routing policy on the CE routers that rejects OSPF routes learned on the backup intra-area link.
Answer: A
NEW QUESTION # 42
Exhibit
You want to use both links between R1 and R2 Because of the bandwidth difference between the two links, you must ensure that the links are used as much as possible.
Which action will accomplish this goal?
- A. Enable per-prefix load balancing.
- B. Disable multipath.
- C. Ensure that the metric-out parameter on the Gigabit Ethernet interface is higher than the 10 Gigibit Ethernet interface.
- D. Define a policy to tag routes with the appropriate bandwidth community.
Answer: D
Explanation:
https://www.juniper.net/documentation/us/en/software/junos/sampling-forwarding-monitoring/bgp/topics/concep
NEW QUESTION # 43
Exhibit
Referring to the exhibit, PE-1 and PE-2 are getting route updates for VPN-B when neither of them service that VPN Which two actions would optimize this process? (Choose two.)
- A. Configure the resolution rib bgp.l3vpn.0 resolution-ribs inet.0 statement on the RR.
- B. Configure the resolution rib bgp.l3vpn.0 resolution-ribs inet.0 statement on the PEs.
- C. Configure the family route-target statement on the PEs.
- D. Configure the family route-target statement on the RR.
Answer: A,D
Explanation:
BGP route target filtering can be configured on PE devices or on route reflectors (RRs). Configuring BGP route target filtering on RRs is more efficient and scalable, as it reduces the number of BGP sessions and updates between PE devices. To configure BGP route target filtering on RRs, the following steps are required:
Configure the family route-target statement under the BGP group or neighbor configuration on the RRs. This enables the exchange of the route-target address family between the RRs and their clients (PE devices).
Configure the resolution rib bgp.l3vpn.0 resolution-ribs inet.0 statement under the routing-options configuration on the RRs. This enables the RRs to resolve next hops for VPN routes using the inet.0 routing table.
NEW QUESTION # 44
......
To prepare for the JN0-664 exam, candidates can take advantage of various resources, including official Juniper Networks training courses, practice exams, and study guides. Passing the JN0-664 exam demonstrates an individual's ability to design, configure, and troubleshoot complex Service Provider networks using Juniper Networks technologies and is a valuable asset for networking professionals looking to advance their careers.
To pass the Juniper JN0-664 certification exam, candidates must have a solid understanding of advanced networking concepts, including routing policies, BGP route manipulation, MPLS VPNs, multicast routing, and Class of Service (CoS) implementation. They must also understand the operation and configuration of Juniper Networks networking devices, such as the MX Series 3D Universal Edge Router, EX Series Ethernet Switches, and SRX Series Services Gateways.
Certification Training for JN0-664 Exam Dumps Test Engine: https://examtorrent.vce4dumps.com/JN0-664-latest-dumps.html